Infocus IN116 User Manual

9Adjusting the imageIf necessary, adjust the height of the projector by rotating the elevator foot to extend the foot.If necessary, rotate the levelin

10Connecting a video deviceYou can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers,

11Shutting down the projectorAuto Off TimeThe projector also has an Auto Off Time feature that automatically turns the projector off after no active s

Problem Solution ResultNo start up screenPlug power cord into the projectorpress power buttonStartupScreenCorrect imageAStartupScreenOnly start up sc

13Problem Solution ResultNo computer image, just the words “Signal out of range” ASignal out of the rangePress the Auto Image button on remoteAdjust c

14Image fuzzy or cropped AAChange the computer's "Resolution" setting to match the projector's resolution (Windows 7: Control Pane

15Image not square Adjust Keystone on keypadSquare imageImage not sharpAspect RatioAuto ImageBrightnessContrastKeystonePresetsSharpnessVolumeCeiling M

A16Image upside downAspect RatioAuto ImageBrightnessContrastKeystonePresetsSharpnessVolumeCeiling MountAdvanced Menu◄ Auto ►Execute505050Presentation5

17The video embedded in my PowerPoint presentation does not play on the screenAABBTurn off the internal LCD display on your laptopEmbedded video plays

18Still need assistance?If you need assistance, visit our website at www.infocus.com/support or call us. Check out our HOW TO section there for additi

1Declaration of ConformityManufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, Oregon 97223-8368 USAWe declare under our sol

19Using the remote controlThe remote uses two (2) AAA batteries (not provided). They are easily installed by removing the cover from the remote’s back

20Using the audioUsing the projector’s speakersConnect the audio source to the Audio In connectors to hear audio through the projector speakers. Ampl

21Using the keypad buttonsMost buttons are described in detail in other sections, but here is an overview of their functions:Power–turns the projector

22Optimizing computer imagesAfter the projector is running and the image is on the screen, you can optimize the image using the onscreen menus. For ge

23Optimizing video imagesAfter your video device is connected properly and the image is on the screen, you can optimize the image using the onscreen m

24Using the menus1 To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are

25Basic MenuTo adjust the following settings, highlight the setting, use the right and left arrows to adjust the values.Aspect Ratio: Aspect ratio is

26Advanced MenuImage: 3D Control:3D Control: allows you to enjoy 3D (stereoscopic) content. Your projector supports two synchronization modes (Externa

ImageSetupStatus/ServiceBasic Menu3D Control...Color...PC...Video...( Advanced Menu )MDL: IN112FW: 0.13Advanced Menu27Setup:Audio Setup...Internal Spe

28Lamp...Programmed Dimming: When enabled, Programmed Dimming enhances con-trast ratios in dark scenes and disables Lamp Low Power. Programmed Dim-min

2Table of ContentsIntroduction 4Positioning the projector 6Connecting a computer source 7VGA connection 7Connecting power 7Optional computer conne

29TimerAuto Off Time: automatically turns the projector off after no signals are detected for a preset number of minutes. If an active signal is recei

30MaintenanceCleaning the lens1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.• Projector must be off and the lens must be at room tem

31Replacing the projection lampThe Lamp Hours timer in the Projector Info menu counts the number of hours the lamp has been in use. Twenty hours befor

321Turn off the projector and unplug the power cord.2 Wait 60 minutes to allow the projector to cool thoroughly. 3 Remove the lamp door, located on to

33INDEXNumerics3D Sync Invert 26AAspect Ratio 25Audio In Computer connector 7Auto Image 25Auto Off Time 29Auto Source 28AV Mute 27BBlank Key 27Blank S

34RRear Project 27Red/Green/Blue Gain 26Red/Green/Blue Offset 26remote control 19Resetting the projector 29SScreen Aspect 10Search Screen 28Service 29

3Important Operating Considerations for Safety• Refer to this guide for proper startup and shutdown procedures.• Follow all warnings and cautions in t

4IntroductionYour new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexib

5Connector panelThe projector provides both computer and video connection options, including:• VGA computer• Composite video• HDMI (IN116 only)•S-vide

6Positioning the projectorTo determine where to position the projector, consider the size and shape of your screen, the location of your power outlets

7Connecting a computer sourceVGA connectionConnect one end of the provided computer cable to the Computer in 1/Computer in 2 connector on the projecto

8Displaying an imagePress the Power button.The Power LED lights blue, and the fans start to run. When the lamp comes on, the start up screen displays.